FAAC Gate Motor Replacement Nationwide

FAAC Gate Motor Replacement: The Hermosa Beach Owner’s Guide

We stock, match, and install FAAC-compatible gate motor replacements throughout Hermosa Beach. A typical installed FAAC motor replacement runs $850-$1,600 depending on the model, and most jobs are done the same day we arrive. Here’s the scene we remember from almost every Hermosa Beach driveway: the gate worked fine for fifteen years, then one morning it groaned, then stopped, and by noon it won’t do anything but sit there. That’s how FAAC motors usually fail - not all at once, but with a few warnings that are easy to miss.

Call (279) 263-9485

For over 42 years, Ironworks Gate Co. has been the gate specialist Hermosa Beach homeowners call when a trusted opener finally gives out. We’re trained on nine major automation brands, FAAC included, and we keep the common replacement motors and parts on our trucks. We are an independent service company, not affiliated with FAAC - which means our loyalty is to your gate, not a manufacturer’s parts program.

Key Takeaways

• Installed FAAC gate motor replacement in Hermosa Beach: $850-$1,600, quoted before work starts.
• We carry the most common FAAC motor units and parts on the truck for same-day service.
• Your price is agreed in writing before we turn a single bolt. No surprises on the bill.
• Every replacement is covered by our 90-Day Done Right Promise, in writing.

Call (279) 263-9485 and a live person picks up - 24 hours a day, every day of the week. Tell us what your gate is doing, and we’ll tell you whether it’s the motor, a capacitor, or something simpler before we even roll a truck.

Which FAAC Models This Applies To

FAAC has been making gate automation since 1965, and the brand shows up on a lot of Hermosa Beach driveways - especially on European-style swing gates and the heavier sliding gates you see in the walk streets and along the Strand. The most common FAAC openers we replace in this area are the 400 series swing-arm operators, the 700 series hydraulic underground units, and the 844/415 sliding gate motors. If your gate is a swing gate with a long stainless arm, you’re likely looking at a 400 series. If the motor sits in a box below ground, it’s probably a 700 series.

Here’s the compatibility gotcha we see most often: FAAC doesn’t make it easy to identify your exact model from a quick glance. The model number is on a small metal plate, usually on the operator body or inside the control box cover. The plate carries a model code and a serial number. Write both down before you call us - it saves a trip. If the plate is gone or unreadable, our technician can identify the unit by the arm geometry, the motor housing, and the control board revision. We match OEM FAAC motors, and where quality aftermarket equivalents make sense, we’ll show you the cost difference and the warranty difference before you choose. For FAAC specifically, OEM is usually the right call for hydraulic units; aftermarket often works fine for the 400 series.

Signs Your FAAC Gate Motor Replacement Is Failing

• The gate moves slower than it used to. A FAAC motor losing speed is usually a capacitor losing its charge or a pump wearing out in a hydraulic unit. It’s the earliest warning sign, and the cheapest stage to fix it.
• It stops mid-travel and reverses. That’s the motor’s thermal overload tripping. The unit is working harder than it should - often because the gate itself has a hinge problem, a sand-packed track, or a wheel bearing gone dry. The motor is telling you something, and it’s not “call next month.”
• You hear a hum but the gate doesn’t move. The motor is getting power and trying to turn. Internal gear wear or a failed capacitor is the usual cause. This is where a homeowner often keeps pressing the remote, hoping for a different result. It won’t be different.
• The gate opens by hand but won’t respond to the remote or keypad. The motor may still be fine, with the failure sitting in the control board or a limit switch. A good tech checks the motor before selling you one. We do, every time.
• The gate slams shut or drifts open on its own. On a FAAC hydraulic system, this often means an internal bypass valve or seal failure. On a 400 series, it’s usually the spring assembly or the limit mechanism. Either way, a drifting gate is a safety problem, not just an inconvenience.

If you’re seeing any of these, call (279) 263-9485. We’ll diagnose it over the phone before we charge you a cent.

Replacement Cost & What’s Included

A FAAC gate motor replacement in Hermosa Beach typically runs $850 to $1,600 installed, depending on the model series and what else we find. Here’s how the cost breaks down:

Your price is quoted and agreed in writing before any work starts. That’s not a courtesy - it’s how we’ve done business since 1984. The quote includes the motor, the labor, the alignment, the limit setting, and a full safety check of the gate’s travel. We stand behind every job with our 90-Day Done Right Promise: if it’s not right, we come back and make it right. No paperwork, no arguing.

Senior and veteran homeowners in Hermosa Beach always receive a 5% discount, and if your repair totals over $250, take the $50 off too.

DIY or Call Us?

Here’s the honest split. You can safely check a few things before calling: confirm the breaker hasn’t tripped, make sure the remote battery isn’t dead, and look at the gate track for obvious debris. If it’s a swing gate and the hinges look rusted, take a good look at them. Metal either holds or it doesn’t - we make sure it holds.

But once the diagnosis points to the motor itself, DIY gets risky fast. FAAC motors involve high-voltage connections, capacitors that hold a charge even after the power is off, and hydraulic lines under pressure. On a 700 series underground unit, working in the vault means handling pressurized fluid and electrical components at the same time. One wrong move and you’re looking at a worse repair than you started with, or a trip to urgent care. We say it plainly so you understand why: motor replacement is not a weekend project. Call (279) 263-9485 and let a background-checked, uniformed technician handle it. We’ll be there when we say.

FAQs