Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lomita
When a welded hinge snaps or a bottom rail rusts through on a gate in Lomita, the fix usually comes down to two things: the right replacement part and a welder who understands what 60 years of salt air does to mid-century steel. We handle both. Ironworks Gate Co. keeps gate hinges, rollers, latch hardware, and weld-ready steel on our trucks, and our crews work throughout Lomita’s residential blocks every week. If your gate is sagging, dragging, or locked shut, call us at (279) 263-9485. We answer the phone with a live person, day or night, and we’ll give you an upfront price before any work begins.
Why Ironworks Gate Co. Is Lomita’s Preferred Gate Parts & Welding Company
Our Gate Parts & Welding team has spent decades working on the exact gates Lomita homeowners keep calling about: original 1950s and 60s wrought-iron driveway gates, tubular-steel side-yard gates, and sliding gates retrofitted into tight shared-driveway arrangements. The calls repeat because the failures repeat. In Lomita, gate posts seat in mid-century concrete footings that crack and shift as the ground settles. Hinges scale from the inside out. Latches seize on rusted barrels. None of that surprises us anymore, and none of it requires a full gate replacement in most cases.
We dispatch from our Los Angeles office, and scheduling a service stop in Lomita is routine for us. Most repair calls are handled in a single visit because we carry the parts that actually fail here: weld-on hinge barrels, replacement steel posts, gate rollers sized for residential tracks, and latch hardware that holds up to the marine layer. The estimate is settled before we turn a wrench, and every weld is covered in writing by our 90-Day Done Right Promise.
Owner Victor Salinas has built this company on a simple rule: a repair is only finished when the gate opens and closes without argument. Our background-checked, uniformed technicians follow the same standard on every Lomita job, whether it is a hinge replacement on a shared driveway off 247th Street or a custom weld on a pedestrian gate near Lomita Park.
Our Gate Parts & Welding Services in Lomita
Hinge Replacement
A gate hinge is the highest-stress point on the whole assembly, and in Lomita it is also the first thing the salt air eats. We carry weld-on and bolt-on hinge replacements sized for the weight of your gate, and we weld new hinge barrels directly onto existing panels when the rest of the gate is still sound. This saves Lomita homeowners thousands of dollars compared to a full gate replacement. Most hinge replacements on a standard driveway gate run 2 to 3 hours on site.
Post Replacement
On Lomita’s small lots, a leaning gate post usually means a cracked mid-century footing, not a bent post. We cut the old steel out, break up and remove the damaged concrete, pour a new footing with proper depth for the gate’s weight, and set a new steel post square and plumb. Then we weld or bolt the gate back in place. A gate that opens when it should, against a post that never moves, is the whole point of replacing the post rather than just shimming it.
Rail Repair
Bottom rails on Lomita’s original iron gates take a beating from ground moisture wicking up through old concrete and settling salt air pooling low. We cut out rusted sections, weld in new steel, and grind the repair flush. When the rail damage is extensive, we quote the cost to fabricate the rail outright before we cut anything, so there is no surprise on the bill.
Custom Welding
Sometimes the right fix is not a part you can order from a catalog. We weld cracked gates, fabricate reinforcement plates for rust-thinned panels, extend gates that have gone out of square, and build custom brackets for tight side-yard installations. If your gate is original to a 1950s Lomita home and worth saving, we would rather weld it than replace it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lomita
Most welded steel gates in Lomita came from local fabricators decades ago, but the automation attached to them wears familiar nameplates. Our techs are factory-trained on Viking, Ghost Controls, and DoorKing systems, and we stock the common replacement parts for these Lomita Gate Motor & Opener systems on our trucks. That means when a Lomita homeowner calls because the gate motor runs but the gate will not move, we can usually diagnose and repair it the same day rather than ordering parts and coming back next week.
Common Gate Parts & Welding Problems We See in Lomita Homes
- Rusted-through bottom rails and lower hinge barrels. The bottom 18 inches of an iron gate in Lomita corrodes to scale years before the top shows visible rust. Ground moisture wicks upward through old footings while the marine layer settles salt low, and the result is a bottom rail that snaps under normal daily use.
- Cracked and shifting mid-century hinge post footings. Lomita’s homes began going up from the late 1940s through the 1960s, and many original post footings were poured shallow by today’s standards. When they crack, the whole gate sags, the latch misses its strike, and the hinge post pulls away from the fence line.
- Sliding gates binding on rusted rollers and racks. In tight side yards where a swing gate will not fit, Lomita homeowners retrofit sliding gates. The track and rollers take abuse from debris and salt air, and when the rollers seize, the gate jams halfway. On a shared driveway near the 405, that backup becomes a real problem for port-area commuters.
- Seized latches and locks on pedestrian gates. The same salt that eats the gate barrel also destroys the internal springs and tumblers in older gate latches. We replace latches with marine-grade or powder-coated hardware that holds up better in Lomita’s specific environment.
Pricing for Gate Parts & Welding in Lomita, CA
A hinge replacement on a typical driveway swing gate in Lomita runs $180 to $420 per hinge, depending on gate weight and whether we are welding a new barrel or replacing the full hinge assembly. Post replacement, including breaking out the old footing, pouring a new one, and setting a steel post, typically falls between $450 and $950 per post. Bottom rail repair runs $250 to $600 per section, and custom welding work is quoted per job based on the length and difficulty of the weld. Sliding gate roller and rack replacement typically lands between $300 and $700.
These are the ranges for Lomita’s market, not a national average. Before a single bolt is turned, we quote a firm price in writing. The number on the invoice is the number on the quote. Call (279) 263-9485 for a free estimate on your specific gate.
We Also Serve Cities Near Lomita
Our crews work throughout the South Bay and harbor corridor, including Gate Parts & Welding in Lomita, Torrance, Rancho Palos Verdes, San Pedro, and Redondo Beach. If you are in one of those neighboring cities and your gate is starting to sag or bind, give us a call. We schedule Lomita stops daily and can usually add a nearby job the same week.
Serving Lomita, CA - Our Local Coverage Area
We’re based in the Lomita area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lomita
Lomita sits 4 to 5 miles from the Pacific and directly adjacent to the Port of Los Angeles corridor, so your gate gets a double dose of salt-laden marine-layer air and port-industrial particulates that inland cities like Gardena or Hawthorne do not experience. Add ground moisture wicking up through aging concrete footings, and the bottom 18 inches of your gate lives in a near-constant oxidation environment. That lower rail and hinge barrel scale from the inside out, often while the top rail still looks fine. Call (279) 263-9485 and we will tell you whether the lower gate can be welded and saved or needs sectional replacement.
Yes, in most cases. If the gate panel itself is still structurally sound, we cut out the scaled hinge barrel, weld in a new steel barrel sized to match the existing hinge pin and plate, and grind the weld flush before repainting. This is a standard repair on Lomita’s original mid-century gates, and it typically costs one-third or less of what a full gate replacement would run.
Yes, we convert swing gates to sliding operation on Lomita lots all the time as part of our Gate Installation - Lomita services. The conversion involves installing a track and rollers rated for your gate’s weight, retrofitting or replacing the automation, and positioning the gate so it slides cleanly without fouling a shared driveway or fence. We will measure on site and give you a written quote that includes the track run, roller hardware, and operator work. Call (279) 263-9485 to schedule a free measure.
When the keypad beeps and the board responds but the gate does not move, the failure in Lomita is usually mechanical rather than electrical: a seized hinge, a rusted roller, or a broken weld where the operator arm attaches to the gate frame. The salt air corrodes the moving parts faster than the electronics fail. We diagnose the mechanical and the electrical side in one visit and give you the price to fix both before we start.
Yes. Any automated gate in Lomita with an operator needs entrapment protection per California safety code: photo eyes or contact edges that reverse the gate if a person, pet, or vehicle is in the opening. If we are repairing or replacing an automated gate, we check that the Gate Access Control in Lomita safety edges and photocells are present and working, and we quote the upgrade if they are missing. That is not an add-on; it is the standard for a legal install. Call (279) 263-9485 and we will explain what your gate needs.
Call Ironworks Gate Co. for Gate Parts & Welding in Lomita
If your gate is sagging, binding, rusted through, or locked shut, call us at (279) 263-9485 for a free estimate. A live person answers, day or night. We will talk through what is failing, give you an honest price range over the phone, and schedule a Lomita visit when it works for you. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Lomita with gate repair, welding, and parts replacement backed by the 90-Day Done Right Promise.